Control Panel

Product Details:

Digital STAR-DELTA motor starter for 3 phase motor and submersible pump,

INTELIGENT MICROCONTROLLER BASED CONTROLLER,

Easy to Use,

Auto Bypass Switch provided. (In Auto mode motor automatically start in 45 seconds without pressing start button and in manual mode motor start by pressing start and stop button)

 

SPP provided

It protect motor from phase failure. In 3 phase motor. Out of 3 phase if any phase failed then motor run in 2 phase and motor winding gets burn.

It protect motor from phase interchange. Out of 3 phase if any phase changed, then motor rotate reverse in this case motor winding gets burn

It protect motor from voltage different between 3 phase, Voltage between 3 phase must be same

 

It has current based dry running. If the motor runs without water then it takes a lower ampere (current) then its actual current. so when the motor’s current gets down from its actual current, it will stop the motor and protect the motor from dry running.

Digital Volt and ampere meter are provided to see system voltage and load current accordingly.

Suitable for motor up to 10 HP

high voltage protection, 

low voltage protection,

Short circuit protection

overload protection

protection bypass facility 

Adjustable overload from 0 to 30 A

Current based dry run protection provided 

Adjustable dry run current from 0 to 30 A

Adjustable voltage limit 

Start and stop buttons are provided

Cyclic timer provided with bypass facility 

Delay timer provided with bypass facility 

On delay timer and off delay time provided

Auto switch provided with bypass facility (When power goes and comes it will auto start the unit)

Auto switch timer provided (when power goes and comes it will start with preset time,) timer adjustable

Input Voltage : 415 VAC

Output Voltage : 415 VAC

High accuracy in over load and dry run current

Auto and bypass mode available

User can bypass all the protection from setting

Isolated supply provided

Error messages shows on display 

RESET button provided to reset unit

High quality METAL Enclosure.

Product Details:

1 hp to 5 hp singal phase starter single phase motor/ ac starter suitable to 0.1 hp to 5.0 hp p/n (40 AMP) relay.

Product Details:

FEATURES :» Operating, economic model» The new version updated 4 digits display» Industrial level of EMC test & higher reliability

SPECIFICATIONS :
INPUT:Input :(AC) 0 - 5 AMP AC Direct OR UP TO 2000/5 CT Selection (Factory Set)

SPECIFICATIONS
INPUT
Input (AC):0 - 5 AMP AC Direct OR UP TO 2000/5 CT Selection (Factory Set)

SPECIFICATIONS:
Supply Voltage:230V AC, ±10%, 50Hz
Range:0 - 2000 AMP AC OR 0-2500 AMP DC (Factory Set)
Accuracy:±1% of FSD
Enclosure Material: Polycarbonate + ABS Plastic
Operating Temp. : 00C 550C
Relative Humidity:Upto 95% RH Non Condensing
Note:30 A AC / 50 A AC / 100 A AC / 200 A AC Direct Available

Product Details:

FEATURES :

» Operating, economic model» Control output RELAY» Industrial level of EMC test & higher reliability» Under voltage, over voltage» Under current, over current» Phase sequence, phase lose» Short circuit» Rotor Lock» Dry run protection» Front & back start & stop

MPD 9611
Features :» 3 Phase Voltage input» 3 Phase AMP input» Supply - 230V AC» Motor Protection Device

SMART 99+
Features :» Inbuilt Star Delta timer» Inbuilt Auto Switch» Front Start Stop Button.» Back Start, Stop, Push, Button Connection.» Auto /manul Selectionst st st » 3 Rely 1 for Protection | 2 for Star | 3 for Deter» Auto Start Dulse Input (Like Compressor)

SMART 99
Features :» With Auto Switch» Star Delta timer

Product Details:

Features:
• LED seven segment Double Display
• Annunciation indicates the type of fault
• Star Delta timer
• Start Stop Button Terminal
• Reset inhibit Function
• Inbuilt Auto Switch

Protection:
• Over Load
• Unbalanced
• Short Circuit
• Single Phasing (phase loss)
• Phase Sequence
• Under current
• Locked Rotor

Product Details:

Features:

Ampere &Volt Controller 
Control output RELAY
The new version updated 4+4 digits display
Industrial level of EMC test & higher reliability
High Voltage &over ampere setting 

INPUT:

Input (Amp.) 0-5 AMP AC Direct OR UP To 2000/5 CT Selection 
Inpt (Volt) 0-650 V AC

OUTPUT:

Control Output: 1C0(1 Relay)
Relay Rating:1C0,7 Amp.230 Volt AC

Specifications:

Supply Voltage: 230v AC, ±10%, 50Hz
Accuracy: ±1% of FSD
Enclosure Material: Polycarbonate + ABS Plastic
Operating Temperature: 0 °C - 55 °C
Relative Humidity: Up to 95% RH Non Condensing

NOTE: 30A AC/50 A AC Direct CT Available